Flowcine | Blackarm w/ Tranquilizer
Owned by Dan B
within a few minutes
100% response rate
Cranfield & Marston Moretaine 69.9 km
Fat Llama covers damages up to £25,000 per item
Information
Flowcine 3-Xis Black Arm The Black arm is a 3-axis dampening system with a additional vibration mount for stabilising roll and tilt errors as well as vertical motion and vibrations. The Black arm is a hardmount system, made for gimbals, that you want to mount on vehicles such as cars, ATVs, boats, snowmobiles etc. Complete Black Arm The Black Arm Complete is for users working with higher loads and carries between 5-32Kg (11-70lbs). It ships with four 7.0mm spring and four 7.5mm springs, that takes the entire range of 5-32Kg. You can use the springs in single (one spring on each side) or dual (two springs on each side) configuration, to precisely achieve the lift needed. The dampening action of all aces, vertical, tilt and roll is created by custom made actuator hydraulic dampers that are fully adjustable. You adjust the damping with a knob that has 22 steps, to precisely dial in the exact amount of damping you need for your shot. The Black Complete ships with a total of six dampers, allowing for dual dampers on each axis if needed, or as spares. Mounting Options Mounting the Black arm is as simple as clamping it on to a standard 48-52mm speed rail. You build a rig onto your vehicle, using standard grip components like speed rail and dual clamps, possibly using Flowcines Universal rack or Stub mount. Then you simply clamp the Black on there, with the two single clamps at the back of the arm. There are several ways to attach your gimbal to the Black arm. The included base plate has hole patterns to match the Freefly Toad in a hole and Cinemilled Universal Ronin mount for easy attachment of the MoVI and Ronin gimbals. Flowcine also make a Mitchell female mount for gimbals that uses the Mitchell connector. On each side of the Blacks head, there are cheese plates suitable to mount batteries or Kenyon gyros on. Flowcine Black Tranquilizer The Flowcine Tranquilizer is the next-generation of vibration isolators, specifically designed around the geometry of a electronic gimbal device. The Flowcine Tranquilizer has been carefully built from ground up to meet the following criterias: Small in size Stabilise lighter gimbals with small amounts of mass Reduce vibrations from lowest possible frequency range and maximise motor torque without getting into self oscillation, which is a common problem with wire rope isolators. The Flowcine Tranquilizer use custom polymers instead of wire rope. We have a system that lets you to go from different types of hardness and amount of polymers, that allows for perfect tweaking of your setup weight, allowing the Tranquilizer to work optimally. The package ships with two sets of polymers, shore 30 and shore 40, and you can easily add more sets if you have a wide span of different gimbals you want to change between, however since the system easily lets you add and subtract the amount, you already have a great range of freedom in weight span with the default package. The Tranquilizer also includes the Flowcine Passive plates. These adds more mass to the system, and lets you dial in the perfect weight and also makes a huge difference compensating incoming hard shocks. These are very easy to add and remove on the fly, while your gimbal is already attached to the system. We include eight of the passive plates in the package, enabling you to add just over 5KG/11LBS to the Tranquilizer. To reduce the problem with when the pan motor goes into self oscillation, we have a design that allows the system to reduce a great deal of incoming vibrations, while at the same time keep the gimbal in check from jittering around the pan axis. This allows you to tune your gimbal/gyrohead with the highest possible pan motor torque settings and the result will be a head that handles high speeds, wind and other dynamics when shooting from vehicles better. All in all, the Tranquilizer is a huge step forward to help you produce the smoothest footage on the planet. We are very proud to release this as an upgrade to your Flowcine Black system! The Tranquilizer ships with two sets of polymers, the shore 30 and shore 40. Softer shores (20/30) are best suited for lighter rigs and/or flat (regular car) road. Harder shores (40/50/60) are more suitable for heavier rigs and/or offroad (ATV) driving. Weights below includes eventual passive plates. Flowcine Black Pro Case It's made in all-black, to perfectly match the Black arm. It features powder coated black metal corners, heavy duty recessed handles and butterfly catches. It also has wheels, so you can roll the case just like a cabin bag. To match the clean exterior, the foam in the Pro case is all black.
Guarantee
Fat Llama covers damages up to £25,000 per item
Cancellation Terms
In case of cancellation 2 days before the rental period, 100% of the rental amount is refunded. If canceled one day before the rental period, 50% of the rental amount is refunded. If you cancel the same day the rental period starts, no refund is made.